Share On

How to install Evo X SST Shift Fork Magnet?

MetaRacing EVO X SST Magnet Shift Fork Upgrade Kit Installation Steps 

Thank you for choosing MetaRacing EVO X SST Shift Fork Magnet Kit .

The kits includes following components:

  • Magnet Shift Fork Head For 2-4 Gears     X1 PCS
  • Magnet Shift Fork Head For 1-3 Gears     X1 PCS
  • Thread Lock Glue                  X1 PCS
  • Adjustment File                  X1 PCS
  • 3mm M4 Screw                  X2 PCS
  • 4mm M4 Screw                  X2 PCS
Installation Steps:
Shift Fork #4:
  • Clean any residual glue from the shift fork #4, ensuring it clean and tidy.
  • Insert the 2-4 shift fork head onto the shift fork rod #4, tighten the securing screw, and use a vernier caliper to measure the distance after installation according to the diagram. Ensure that the distance between the ends of the fork head and the fork rod is between 105.7mm and 105.85mm, 105.85 mm as recommended distance .
    evo x sst shift fork magnet install -1
    evo x sst shift fork magnet install -1
evo x sst shift fork magnet install -2
evo x sst shift fork magnet install -2
  • It’s necessary to adjust the shift fork rod according to the provided data. This is because the length of each shift fork rod may not be exactly the same. You might need to use a file to modify the shift fork rod, ensuring it meets the required length after installation. Always make sure the screws are securely tightened each time you take measurements.
  • Remove the fork head from the shift fork rod, apply the provided thread lock glue inside the groove of the fork head, and install it onto the shift fork rod. Apply appropriate thread lock glue to the screw and tighten it securely. Then, measure the installation length again, aiming for 105.7mm to 105.85 mm(Recommend)
evo x sst shift fork magnet install -3
evo x sst shift fork magnet install -3
    • Allow the installed components to sit undisturbed for 24 hours to ensure the complete curing of the adhesive. Afterward, you’re ready to install them in the vehicle.

    Notice: If the P1833 error occurs, the installation length should be increased. If the P1879 error occurs, reduce the installation length. You can use the Muts tool to read the data stream and then adjust the length appropriately.

    Shift Fork #2:
    • Clean any residual glue from the shift fork #2, ensuring it clean and tidy.
    • Insert the 3-5 shift fork head onto the shift fork rod #2, tighten the securing screw, and use a vernier caliper to measure the distance after installation according to the diagram. Ensure that the distance between the ends of the fork head and the fork rod is between 79.15mm and 79.20mm, 79.15 mm as recommended distance .

    evo x sst shift fork magnet install -4
    evo x sst shift fork magnet install -4
    evo x sst shift fork magnet install -5
    evo x sst shift fork magnet install -5
    evo x sst shift fork magnet install -6
    evo x sst shift fork magnet install -6
    evo x sst shift fork magnet install -7
    evo x sst shift fork magnet install -7

    • It’s necessary to adjust the shift fork rod according to the provided data. This is because the length of each shift fork rod may not be exactly the same. You might need to use a file to modify the shift fork rod, ensuring it meets the required length after installation. Always make sure the screws are securely tightened each time you take measurements.
    • Remove the fork head from the shift fork rod, apply the provided thread lock glue inside the groove of the fork head, and install it onto the shift fork rod. Apply appropriate thread lock glue to the screw and tighten it securely. Then, measure the installation length again, aiming for 79.15mm to 79.20mm, 79.15 mm as recommended distance .
    evo x sst shift fork magnet install -8
    evo x sst shift fork magnet install -8
    • Allow the installed components to sit undisturbed for 24 hours to ensure the complete curing of the adhesive. Afterward, you’re ready to install them in the vehicle.

    Notice: If the P1827 error occurs, the installation length should be increased. If the P1877 error occurs, reduce the installation length. You can use the Muts tool to read the data stream and then adjust the length appropriately.

    If any issue or need support, please feel free contact us:

    WhatsaPP: +86-15602939862

    Mail:  danny@cdmperformance.com

    Share On

    Similar Posts